Loading...
6-15-23 - Ordinance to Amend & Reenact Sec. App. A. Sub: Article 5 (Subdivision Ord) AN ORDINANCE TO AMEND AND REENACT THE FOLLOWING SECTION OF APPENDIX A. SUBDIVISIONS: ARTICLE 5 (DEVELOPMENT STANDARDS) WHEREAS,the Board of Supervisors of Isle of Wight County,Virginia,has the legislative authority to make reasonable changes to the ordinances that govern the orderly growth and development of Isle of Wight County; and WHEREAS, the Isle of Wight County Board of Supervisors is also concerned about the compatibility of uses on public and private lands within Isle of Wight County and seeks to allow flexibility in the administration of the ordinance regulations while protecting the health, safety, and general welfare of present and future residents and businesses of the County. NOW, THEREFORE, BE IT ORDAINED by the Isle of Wight County Board of Supervisors that Article V of Appendix A, Subdivisions, of the Isle of Wight County Code be amended and reenacted as follows: Article 5. Development Standards 5.1. Land suitability. 5.1.1. The subdivision agent shall not approve the subdivision of land if, from adequate investigations conducted by all public agencies concerned, it has been determined that in the best interest of the public the site is not suitable for platting and development purposes of the kind proposed. 5.1.2. Land subject to flooding and land deemed to be topographically unsuitable may not be platted for residential occupancy, nor for such other uses as may increase danger of health, life or property or aggravate erosion or flood hazard. 5.1.3. Lands within the subdivision that are subject to flooding or deemed to be topographically unsuitable for residential occupancy must be reserved for uses that are not endangered by periodic or occasional inundation or do not produce conditions contrary to public welfare. 5.2. Responsibility for improvements. A. The applicant is responsible for providing all required improvements in conformance with the requirements of this ordinance and any other applicable ordinances, codes, rules, or regulations. All costs associated with the installation of said improvements remains the responsibility of the applicant and any bond or other fiscal surety posted as a condition of approval may not be released until construction has been inspected and approved by the appropriate engineer or regulating autharity (see section 3.2.8.E, performance guarantee). The following forms of fiscal surety will be accepted: Cash Cashier's check Certified check Page l of 21 Surety bond Letter of credit Any other form of surety must be approved by the Isle of Wight County Attorney prior to acceptance. B. The amount of such fiscal surety shall not exceed the total of the estimated cost of construction based on unit prices for new public or private section construction in the county and a reasonable allowance for estimated administrative costs, inflation, and potential damage to existing roads or utilities, which shall not exceed ten (10) percent of the estimated construction costs. 5.3. General subdivision design. The following principles shall guide the design and layout of proposed subdivisions in the county. 5.3.1. Subdivisions should be designed to protect and maintain existing natural features on the site, including existing terrain, drainageways, stands of trees, and other elements. Where possible, existing trees and other vegetated areas should be utilized to satisfy landscaping and buffering requirements. Naturally occurring drainage paths should be maintained and utilized to the extent possible. 1. No lot shall be designed, approved or employed for use in which an area more than thirty (30) percent of the prescribed minimum lot area is comprised of one (1) or more of the environmentally sensitive areas referenced in the net developable calculations of the zoning ordinance. This shall not apply to lots specifically created exclusively to preserve and maintain environmentally sensitive areas, as approved by the zoning administrator. 5.3.2. Additional open spaces suitable for passive and active recreational use should be reserved where possible. 5.3.3. Streets and lots should be laid out to provide a coordinated and efficient use of land and minimize the need for costly expansion of the external roadway system outside of the subdivision. This may include providing an interconnected network of sCreets within the subdivision and providing both roadway and pedestrian connections to adjacent compatible developments. 5.3.4. Construction of the subdivision should be undertaken in a manner that minimizes the clear cutting and mass grading of land. 5.3.5. No singular subdivision shall extend over a political boundary. 5.4. Subdivision types. 5.4.1. Purpose. The zoning ardinance establishes twelve (12) different base zoning districts. These zoning districts are based on the intended character of development located within the district. Understanding that the character of the development also contains implications for subdivision design, certain standards within this ordinance have been tailored to accommodate appropriate layout and construction. This may not be construed as allowing any use or development that is not in conformance with the zoning ordinance z or the zoning requirement for residential development(reference section 3.2.3.C, zoning requirements in this ordinance for information on required zoning prior to subdivision approval). 5.4.2. Subdivision types. A. Rural subdivisions. Rural subdivisions are those subdivisions in the following zoning districts: l. RAC Rural Agricultural Conservation 2. RR Rural Residential B. Other residential, commercial, industrial, civic, miscellaneous, and planned development subdivisions. Subdivisions in the following zoning districts: 1. SE Suburban Estate 2. SR Suburban Residential 3. UR Urban Residential 4. VC Village Center 5. NC Neighborhood Conservation 6. LC Limited Commercial 7. GC General Commercial 8. LI Limited Industrial 9. GI General Industrial 10. GIC General Industrial Conservation 11. PD-R Planned Development - Residential 12. PD-MH Planned Development - Manufactured Home 13. PD-CP Planned Development - Corporate Park 14. PD-MX Planned Development - Mixed Use I5. PD-IP Planned Development - Industrial Park 5.5. Name duplication. The name of a proposed subdivision may not duplicate nor closely approximate the name of an existing subdivision within the county. 5.6. Subdivision activity in Chesapeake Bay Preservation Area. Any subdivision activity subject to the provisions of this ordinance and contained wholly or in part within the designated Isle of Wight County Chesapeake Bay Preservation Area must be designed and perfarmed in compliance with the Isle of Wight County Chesapeake Bay Preservation Area Ordinance. Page 3 of 21 5.7. Subdivision activity in wetlands. Development activities within wetland areas may require additional permits from entities other than Isle of Wight County, including the US Army Corps of Engineers, the Virginia Department of Environmental Quality, the Virginia Marine Resources Commission, and other agencies. 5.7.1. Any subdivision activity proposing to fill, build in, on or in any way disturb any waterway or wetland area must obtain approval from the Virginia Department of Environmental Quality (VDEQ), the US Army Corp of Engineers (COE) andlor the county wetlands board prior to initiating any construction. 5.8. Stormwater management. 5.8.1. Applicability. A. Applicants may be required to provide stormwater management improvements or make other improvements to the existing drainage system to address water quantity concerns, water quality concerns, or both if the proposed development will increase potential f7ood damages to existing properties or significantly increase pollutant levels in downstream receiving waters. B. The need for stormwater management improvements to address offsite impacts must be determined by the county engineering division. The applicant shall be required to provide surety to guarantee completion of required improvements prior to final plat approval. 5.8.2. Stormwater management program. A. Subdivision applications disturbing one (1) or more acres of land or two thousand five hundred (2,500) square feet within the Chesapeake Bay watershed, as well as all modifications to existing stormwater systems shall require the submittal of a stormwater management plan in accordance with the county stormwater management ordinance. B. When a separate stand-alone stormwater management plan is not required, the proposed stormwater management improvements must be indicated on the preliminary plat, construction plans, and final plat. C. The stormwater management concept plan and stormwater management final plan shall be prepared in accordance with the county stormwater management ordinance. 5.8.3. Stormwater design standards. A. The applicant must provide all necessary information needed to determine what improvements are necessary to properly develop the subject property, including contour intervals, drainage plans and proposed stormwater management improvements. B. Stormwater management improvements must be designed and installed in accordance with the Isle of Wight County Stormwater Management Ordinance as well as all other applicable codes and ordinances. Plans for all improvements must include a certification by a properly qualified engineer or surveyor that proposed improvements, Page 4 of 21 when properly installed, will be adequate for proper development and conforrn to all design standards and requirements. C. Piping and modification of streams and other natural watercourses should be minimized and shall be considered on a case-by-case basis to determine if it is necessary and environmentally sound. Such facilities must be designed, constructed and maintained to minimize flooding, protect downslope properties, preserve water quality, and adequately transport existing and projected stormwater flows. D. The use of best management practices (BMPs) to manage stormwater is strongly encouraged. Examples of BMPs include: Bioretention and biofiltration, rain gardens, infiltration, detention, and structural controls. Note: The following table illustrates some(but not all) of the BMPs that may be considered. Exam le BMP Illustration Rain arden -� Roadside Infiltration Swale "- D Detention Basin Media Filter �� �. F. When stormwater ponds or management facilities are used, they shall be designed, landscaped, and integrated into the overall site design as a community amenity as follows: t� �� "�=`_. .; •Te�i::' . ;; , „ �:`" � � � t t t ;; i , � ; _' � �." r:� �y `" _ :y +� °;�� � �.. �ti - t : � R @�i.;' � � �k �"�' ' t - E,t�-;a� t. . r� x, • '',�, ,► ,. .-�v � �k .'� ::... 4 � "���' 6 ��,y� '�r .1 � '��T, '�` '°� 'b, �.�'� . :��1 ��. 3f,# �� Stor�ar.a�er Pand used asHr�n,'y l. Stormwater retention and detention areas shall meander through the development as a greenbelt, rather than as a single basin. Stormwater retention areas shall be improved so as to be useable and accessible for recreational purposes. Retention areas shall be designed such that when inundated (following a rain event), they shall remain usable for their designated recreationa] purposes. G. Stormwater retention and detention areas shall be designed with a natural character and shall be constructed of natural materials. Terracing, berming, and contouring is required in order to naturalize and enhance the aesthetics of the basin. Such features shall be approved by the subdivision agent. Basin slopes may not exceed a three (3) to one (1) slope and shall be designed to permit ready access for maintenance. In Page 5 of 21 addition, the final design must incorporate child safety features through signage or other appropriate means. H. Roadway drainage improvements must be provided in accordance with the VDOT Drainage Handbook. Drainage facilities located within the right-of-way must be approved by the VDOT engineer prior to dedication. I. The subdivision agent may require that easements for drainage through adjoining property be provided by the applicant. An access easement that is at least ten (10) feet in width may be required to allow routine maintenance and repairs to stormwater facilities. 5.8.4. Maintenance and ownership. A. Maintenance bond required. The applicant shall submit a maintenance bond on a form acceptable to the county until the stormwater facility is turned over to the property owner's association. B. Ownership. Stormwater facilities shall be owned and maintained by a property owner's association (POA) representing owners of the land within the subdivision. Membership in the association shall be mandatory and automatic for all landowners of the subdivision and their successors. The POA shall have lien authority to ensure the collection of dues from all members. C. Maintenance agreement. A stormwater management facility maintenance agreement, maintenance easement agreement and farmal maintenance covenant shall be submitted and recorded with the clerk's office of the circuit court priar to the issuance of any permits and shall be binding on all subsequent owners of land served by the facility. The stormwater management facility maintenance agreement shall be prepared in accordance with the requirements of the county starmwater management ordinance. D. Failure to maintain. In the event the POA responsible for maintenance of the stormwater facility fails to maintain all or any portion in reasonable order and condition, the county may assume responsibility for its maintenance and may enter the premises and take corrective action, including the provision of extended maintenance. The costs of such maintenance may be charged to the POA, ar to the individual property owners that make up the association and may include administrative costs and penalties. Such costs shall become a lien on all subdivision properties. 5.9. Streets. 5.9.1. General standards. A. All streets in the proposed subdivision shall be designed and constructed in accordance with the minimum requirements found in this section at no cost to the county. B. Road widening and right-of-way dedication must meet or exceed VDOT standards. C. Unless specifically modified in this ordinance, all new streets must be public and improved to comply with the VDOT road and bridge standards. 5.9.2. Description of public and private streets. Page 6 of 2l A. Public street. A street (or portion of a street) that has been improved to comply with the requirements of this ordinance and the VDOT subdivision street design guide and has been accepted or is proposed to be accepted into the state primary or secondary road system. B. Private street. A street (or portion of a street) that has not been accepted into the state primary or secondary road system. [5.9.3. Reserved.] 5.9.4. Connectivity requirements. A. Required. Unless exempted below, stub outs are required on each side of a subdivision (as defined by each of the cardinal directions) as follows: 1. Rural subdivisions. At least one (1) stub out for every two thousand eight hundred (2,800) linear feet on any single side of the proposed development. 2. Other subdivisions. At least one (1) stub out for every one thousand four hundred (1,400) linear feet on any single side of the proposed development. B. Exemptions. 1. Stub outs are not required when the existing street pattern in the area of the proposed subdivision already provides for vehicular connections at intervals no greater than one-half('/z) mile apart in rural subdivisions, and one-quarter('/a) mile apart in all other subdivisions. 2. Stub outs may not be required adjacent to existing development that has not made any accommodation for such connections or to adjoining sites that are permanently protected from development through conservation easements or ownership that precludes development. 3. Stub outs may not be required if the only point of access would require crossing floodplains, wetlands, or other similar natural features. 5.9.5. Street classification. A. Guidelines. 1. In all new subdivisions, streets that are dedicated to public use shall be classified as provided in this section; 2. The functional classification is based on the general design and the projected volume of traffic to be carried by the street, stated in terms of the number of average daily vehicle trips per day; 3. The number of dwelling units to be served by the street may be used as an indicator of the number of trips but is not conclusive; 4. Whenever a proposed subdivision street continues an existing street that previously ended outside the subdivision or it is expected that a subdivision street will be continued beyond the subdivision at some future time, the classification of the proposed street is based upon the entire street, both within and outside of the subdivision. Page 7 of 21 B. Functional classification. 1. Arterial (primary).A street specifically designed to move high volumes of traffic from collector streets through the county and not designed to serve abutting lots except indirectly through intersecting streets. Arterial streets include all U.S. Highways, state primaries with one-, two- or three-digit numbers, and any other streets which the subdivision agent determines as functionally equivalent to these transportation department classifications. 2. Collector (secondary).A relatively low-speed, low-volume street that provides circulation within and between neighborhoods. Collector streets usually serve short trips and are intended for collecting trips from local streets and distributing them to the arterial network. They also form a secondary network of cross county connectivity. It is intended to serve, directly or indirectly, up to one hundred (100) dwelling units and is intended to carry up to eight hundred (800) average daily vehicle trips per day. 3. Local (secondary).These streets provide direct access to adjacent land and serve travel of short distances as compared to the higher systems. It serves or is designed to serve no more than twenty-�ve (25) dwelling units ar expected to or does handle between seventy-five (75) and two hundred (200) average daily vehicle trips per day. 4. Alley (private).A service easement which affords only a secondary means of access to abutting property for utilities, sanitation, garages, backyards and any accessory units and are not intended for general traffic circulation 5. Service drive (marginal access street, frontage road).A street that is parallel to and adjacent to an arterial street and that is designed to provide access to abutting properties so that these properties do not directly access the arterial street. Properties fronting on a service drive are somewhat sheltered, and the flow of traffic on the arterial street is not impeded by numerous direct driveway access points from a large number of properties. 5.9.6. Street alignment and layout. A. The proposed street layout in a new development must be coordinated with the existing street system with connections made at all stub outs existing on adjacent properties. Per chapter 11 of the comprehensive plan, the street layout shall be a modified grid pattern adapted to the topography and unique features of the site. Where full connection cannot be made as a result of the topography of the site being developed, the subdivision agent may allow the installation of a cul-de-sac or other turnaround facility in accordance with section 5.9.10 of this ordinance. B. Half streets along the boundary of land proposed for subdivision are prohibited (this is not deemed to prohibit the construction of service drives or one-way streets). C. Street intersections should be as close as possible to ninety (90) degrees (right angle), and may not be less than seventy (70) degrees without express approval by the subdivision agent, in consultation with VDOT. Page 8 of 21 D. Whenever a proposed subdivision contains or is adjacent to a limited access highway or expressway, provisions must be made for a service drive or marginal access street approximately parallel to such right-of-way at a distance suitable for an appropriate use of the land between such highway and the proposed subdivision. Such distances shall be determined with due consideration of the minimum distance required for ingress and egress to the main thoroughfare. E. The proposed street arrangement may not cause unnecessary hardship to owners of adjoining property when they plat their own land and seek to provide for convenient access to it. Where, in the opinion of the subdivision agent, it is desirable to provide for street access to adjoining undeveloped property, proposed streets must be extended by one (l) of the following methods: 1. The developer may construct a stub out street in conformance with section 5.9.10, cul-de-sac streets ar section 5.9.11, loop lanes. Where stub outs are less than fifty (50) feet in length and do not provide access for nonresidential or multifamily uses, the subdivision agent may waive the requirement for a turnaround facility. 2. The developer of the proposed subdivision may dedicate a stub out easement to the county of sufficient width to accommodate the future extension of the subject street when the adjacent property is developed. If this alternative is selected, the developer must provide a construction bond sufficient to pay for the proposed improvements. The developer must provide notice to all future owners of lots fronting on the easement that a roadway may be installed at a future date. This easement and notice must be prominently indicated on the final subdivision plat. The applicant must post a sign of a design approved by the county. 5.9.7. Traffic calming. Traffic calming measures must be installed in accordance with VDOT standards. When traffic calming measures are proposed, such measures should be shown on subdivision construction plans and profiles or site plan submissions. If desired, a camprehensive traffic calming plan indicating proposed calming measures can be submitted for review and approval for the entire development with the first preliminary plat application. 5.9.8. Street grades. The grades of streets submitted on subdivision plats shall be approved by the county engineering division in consultation with the VDOT engineer. Wherever feasible, street grades may not exceed five (5) percent. 5.9.9. Street cross-section. A. Applicability. Unless the use of alternative street design standards has been authorized (see section 5.9.16), all public and private streets must comply with VDOT street cross-section standards. B. Pavement construction requirements. 1. Pavement design for new public and private streets must be in accordance with VDOT standards. 5.9.10. Cul-de-sac streets. A. Description. Generally, cul-de-sac streets (minor terminal streets) are designed to have one (1) end permanently closed. Cul-de-sacs should be avoided unless natural barriers Page 9 of 21 (wetlands, topography, floodplains) limit the opportunities for an interconnected grid network. B. Length. 1. The length of a cul-de-sac street is measured from the end of the right-of-way of the turnaround portion of the cul-de-sac street to the nearest intersection with a street which provides a means of direct or indirect egress from the subdivision. 2. Cul-de-sac streets may not exceed the greater of five hundred (500) linear feet or ten (10) times the width of the lot(measured at its narrowest point). C. Landscaped medians and islands. 1. All cul-de-sac streets must have a landscape island at the center of the turnaround circle a minimum of fifty-four (54) feet in diameter for any cul-de-sac on a street serving more than sixteen (16) or more dwelling units or any use other than residential, and twenty-four (24) feet in diameter for any street serving fifteen (15) or less dwelling units and only residential uses. These islands may be designed as bioretention gardens and surface grading of cul-de-sac may be adjusted up to ten (10) percent to allow water to drain to the landscape island. 2. In the event that a cul-de-sac street is authorized to exceed eight hundred (800) feet in length, then such a cul-de-sac street shall be designed with a landscaped median that divides the cul-de-sac street into two (2) distinct and separate lanes. However, such a cul-de-sac street may be continuously undivided for the final two hundred (200) feet of the street. This undivided section is measured from the end of the right-of-way of the turnaround portion of the cul-de-sac street. 3. Median breaks must be provided at street intersections and at other appropriate locations along the cul-de-sac street to ensure safe and efficient traffic circulation and delivery of emergency services. One (1) median break should occur approximately every four hundred (400) feet of the cul-de-sac street. 4. When the cul-de-sac street serves commercial, institutional, or industrial lots or structures, the requirement for a landscaped median or island may be modified or waived by the subdivision agent upon approval by the board of supervisors due to the additional fire protection requirements incorporated into such structures. 5. All non-vehicular movement areas such as medians and islands shall be located in the right-of-way of the cul-de-sac street. D. Turnaround. New cul-de-sac streets must terminate in a circular vehicle turnaround. The minimum diameter(measured to the edge of pavement or face of curb) of this turnaround is: 1. Sixty (60) feet on residential cul-de-sac streets serving fifteen (15) or fewer dwelling units and no other uses. 2. Ninety (90) feet on all other cul-de-sac streets. E. Other terminal access (dead-end) streets. Page ]0 of 21 1. "T" Turnarounds. T-turnaround are discouraged. The subdivision agent may approve the use of"T" (shaped) turnarounds in lieu of cul-de-sacs when upgrading existing streets. 2. Stub out streets. a. Description. Stub out streets are continuations of internal streets to the perimeter of a project for future connection to adjacent properties. b. Standards. A temporary cul-de-sac (standard or "T") must be provided at the end of all stub out streets. The right-of-way lines and constructed pavement must be extended to the boundary line of the proposed subdivision if the adjacent property is undeveloped. Suitable barricades and "Street Closed" signs must be erected at the street end during the construction phase. At the completion of the street construction, "End of Street" signs must be erected at the street end. The following notation must be placed on the subdivision plat: "Future access connection for adjacent development, to be constructed upon the extension of the street." 5.9.1 1. Loop lane. A. Description. A loop lane is the recommended alternative to the use of cul-de-sac streets, "T" turnarounds, or other terminal access streets. Loop lanes shall be designed as two (2) one-way lanes separated by a central bioretention area or grassed, planted median at least sixty (60) feet in width. B. Length. Loop lanes may not exceed five hundred (500) linear feet from the point of intersection with the connecting roadway. 5.9.12. Alleys. Dead-end alleys should be avoided wherever possible. If dead-end alleys are unavoidable, the end shall be provided with adequate turnaround facilities (see section 5.9.10.E, above) as determined by the subdivision agent. 5.9.13. Planting strips. When required, planting strips shall be installed in accordance with the current VDOT Subdivision Street Guide. Additional planting strip width may be required to avoid conflict with required utility easements. 5.9.14. Street names. A. Proposed streets which are obviously in alignment with other already existing and named streets must continue the names of the existing streets. Names of existing streets may not be changed except by approval of the board of supervisors. B. In no case may the names of a proposed street duplicate existing street names irrespective of the use of the suffix "road", "street", "avenue", "boulevard", "drive", "way", "place", "lane", or "court". C. Street names must be indicated on the preliminary and final plats, and must be approved by the subdivision agent in consultation with the county's information technology and emergency management departments. Page l 1 of 21 5.9.15. Street identification signs. Street identification signs of a design approved by the subdivision agent and VDOT, where applicable, must be installed at all intersections. 5.9.16. Alternative street design standards. The use of VDOT authorized alternative street design standards for subdivisions located in a planned development may be granted by the board of supervisars following a recommendation from the planning commission. (l 1-18- 21(1).) 5.10. Blocks. 5.10.1. Block length. Blocks shall be a minimum of two hundred fifty (250) feet and a maximum of five hundred (500) feet in length. The subdivision agent may allow longer block lengths in limited cases where shorter block lengths would be impractical. 5.10.2. Block width. Blocks shall be wide enough to allow two (2) tiers of lots at minimum depth as required by the underlying zoning. The subdivision agent may approve a single tier of lots of minimum depth where environmental conditions restrict the lot layout. 5.10.3. Block orientation. Where a proposed subdivision will adjoin a major road, the subdivision agent may require that the greater dimension of the block front or back upon such major thoroughfare to avoid unnecessary ingress or egress. 5.11. Lots. 5.1 1.1. Shape. Lots should be designed, arranged, and shaped so that they provide satisfactory and desirable sites for buildings, be properly related to natural topography, and conform to requirements of this ordinance and the zoning ordinance. Lots within the DSDs shall be generally regular in shape and may not contain peculiarly shaped elongations solely to provide necessary square footage of area which would be unusable for normal purposes, the only exception to this rule being elongations for use as access within a flag lot. Lots outside the DSDs should be designed to follow natural features whenever possible, and such lots should seek to provide for agricultural, forestal or open space use of the land. For lots with a width of sixty (60) feet or greater, lot proportions should provide approximately two and one-half(2.5) feet of lot depth for every one (1) foot of lot width. 5.l 1.2. Location. All lots shall front on a street dedicated by the subdivision plat, or on an existing publicly dedicated street, or on a road within the Virginia Department of Highways system. With the exception of corner lots, no lots shall have double frontage on any road unless suitably bermed. When a proposed subdivision abuts one (1) side of any existing street or road that is shown on a plat of record or has been included in the system of highways and streets in Isle of Wight County, the subdivider shall be required to dedicate one-half('/z) of the land necessary to comply with the applicable minimum VDOT right-of-way requirements. 5.1 1.3. Corner lots. Corner lots shall have extra width sufficient to maintain required building setbacks from both streets as specified in the zoning ardinance or as determined by the subdivision agent. S.l 1.4. Side lines. Side lines of lots shall be approximately at right angles or radial to the street line. Page I 2 of 21 5.11.5. Remnants. All remnants of lots below minimum size left over after subdividing of a tract must be added to adjacent lots or otherwise disposed of rather than allowed to remain as unusable parcels. 5.1 l.6. Separate ownership. Where the land covered by a subdivision includes two (2) ar more parcels in separate ownership, and lot arrangement is such that a property ownership line divides one (1) or more lots, the land in each lot so divided shall be transferred by deed to single ownership, simultaneously with the recarding of the final plat. Said deed is to be deposited with the clerk of the court and held with the final plat until the subdivider is ready to record same, and they both shall then be recorded together. 512. Sidewalks and paths (pedestrian and bicycle facilities). 5.12.1. GeneraL Sidewalks and paths shall be designed to provide a safe and convenient pedestrian circulation system within the subdivision as well as connections to adjacent areas. These systems should be designed to connect with all elements within the development, adjacent areas, existing sidewalks/greenways, and transit stops and may include sidewalks along public or private streets, bike lanes on roadways, greenways, and walkways and trails in alternative locations as appropriate. 5.12.2. Sidewalks. A. Where a sidewalk is specifically required by this ordinance, it must be located within the right-of-way. However, the subdivision agent may approve alternate walkway ]ocations when it is determined that the location within the right-of-way is not feasible. B. Sidewalks located within the public right-of-way must be constructed to VDOT standards. Curb ramps or sloped areas must be provided where sidewalks cross curbs, as required by current Americans with Disabilities Act standards. Inlets may not be located within sidewalks. Catch basin and manhole frames must have closed lids when located within the sidewalk. C. On roads with curb and gutter, sidewalks must be separated from the back of curb by a planting strip in accordance with the VDOT Subdivision Street Design Guidelines, dependent upon the presence of landscaping. Trees are to be located between the sidewalk and the curb or within a landscape easement adjacent to the right-of-way with the maintenance responsibility assigned to a property owner's association. Species of trees should be consistent with the recommendations found in the VDOT Subdivision Street Design Guide which will not interfere with nearby utilities or other public improvements. D. Along roads with shoulders and ditches, sidewalks must be located behind the roadside ditch or a guardrail. The subdivision agent may authorize the use of alternative walkways ([section] 5.12.3) when shoulders and ditches are used. E. In order to be accepted for dedication by VDOT, sidewalks must be located completely within the right-of-way and constructed in compliance with the VDOT Subdivision Street Design Guide. F. Any proposed subdivision that includes, directly abuts or provides direct access to a proposed greenway location as identified in the county bicycle and pedestrian master Page 13 of 21 plan, must provide a greenway easement or sidewalk to either continue the path in its intended location or allow unencumbered access to the greenway for all future residents. 5.12.3. Alternative walkway. A. Pedestrian walkways may be provided outside of the right-of-way when the subdivision agent determines the walkway will have the same functionality as the conventional sidewalk required. B. The subdivision agent may approve alternative construction materials including asphalt, crushed stone> and other surfaces. 5.12.4. Bicycle lanes. When a proposed street may serve as a potential connection between identified bicycle routes in the county bicycle and pedestrian master plan, on-street bicycle lanes must be installed in conformance with VDOT Subdivision Street Design Guide. 5.13. Water and sewer facilities. 5.13.1. Public facilities. A. Water. 1. Connection requirements. a. Unless specifically exempted below, all subdivisions located within a development service district (DSD) and all subdivisions that have public water service passing adjacent to the subject property (whether or not in a DSD) must connect to the Isle of Wight [County] public water system and the service shall be extended to all lots and all fire hydrants within the subdivision. b. The subdivision agent may grant an exception to the connection requirement far subdivisions of four (4) ar fewer total lots that do not have public water service passing adjacent to the property (whether or not in a DSD). 2. Construction standards. All water supply and distribution systems, whether public or private, shall be installed by the subdivider in accordance with the design standards and specifications for water, construction and improvements in Isle of Wight County and shall require design approval of the subdivision agent, in consultation with the department of public utilities and other appropriate review entities. Mains shall be sized for friction loss and must be shown on construction plans (along with fire hydrants). 3. Dedication to the county. All water supply and distribution systems that are connected to the county's public water service shall be dedicated to the county upon completion and after public utilities/engineering have approved the completed facility's construction and verified proper operation. B. Sewer. 1. Connection requirements. Page 14 of 21 a. Unless specifically exempted below, all subdivisions located within a development service district (DSD) and all subdivisions that have public sewage service passing adjacent to the subject property (whether or not in a DSD) must connect to the Isle of Wight [County] public sewage system and the service shall be extended to all lots within the subdivision. Septic tanks will not be permitted. b. The subdivision agent may grant an exception to the connection requirement for subdivisions of four(4) ar fewer total lots that do not have public sewage service passing adjacent to the property (whether or not in a DSD). In such case, private facilities will be allowed in conformance with section 5.13.2, private facilities (below). 2. Construction standards. Every subdivision shall be provided by the subdivider with a satisfactory and sanitary means of sewage collection and disposal in accordance with the design standards and specifications for sewerage construction and improvements in Isle of Wight County, Virginia, and meeting the approval of the subdivision agent. 3. Dedication to the county. All sewage facilities that are connected to the county's public sewage service shall be dedicated to the county upon completion and after public utilities/engineering have approved the completed facility's construction and verified proper operation. S.13.2. Alternative discharge/private facilities. A. Nothing in this ordinance shall prevent the installation of privately owned water and/or sewerage facilities in areas where public facilities are not available or their installation would be cost prohibitive. When private facilities are provided: 1. A conditional use permit may be required (see zoning ordinance). 2. The facilities must meet all the requirements of the Virginia Water Control Board, the Virginia Department of Environmental Quality, the Virginia Department of Health, Isle of Wight County Department of Public Utilities, and any other state or local regulation having authority over such installation, including the provisions of the zoning ordinance for alternative discharge sewage disposal systems; and 3. Upon completion of the facilities, the developer or owner may be required to convey, without cost, said facilities and all appurtenances, including sufficient land, easements and rights-of-way, to the county. B. Lots may be required to provide greater area than the minimum required for the zoning district where individual septic tanks or individual wells are used if the health official determines that there are factors of drainage, soil and condition or other conditions to cause potential health problems. Where septic tanks are to be used for sewage disposal, the subdivision agent shall require the submittal of an onsite sewage disposal system subdivision review package from an authorized onsite soil evaluator, a sewage disposal system certification letter as issued by the health department or a sewage disposal system construction permit as issued by the health department prior to preliminary plat approval or, if a preliminary plat is not required, prior to subdivision approval. Page 15 of 21 C. When individual (on-site) septic sewage disposal systems are used on newly created lots within the Chesapeake Bay watershed, each lot must contain an adequate area of suitable soil for the location of the primary sewage disposal system and at least one (1) reserve drainfield must be provided totally within the boundary lines of said lot. D. Alternative discharge sewage systems shall be subject to review and approval by the state health department and the Department of Environmental Quality. E. Lots to be served by individual (on-site) sewage disposal systems shall be pumped out as required by the septic pump-out ordinance in article 6 of the Chesapeake Bay Preservation Area Ordinance. F. Subdivisions with fifteen (15) or more lots that will not be served by a county-owned or contracted water system shall be served by a privately-owned, complete central water supply and distribution system which provides service to each and every lot. Subdivisions to be developed in phases shall count the total number of lots to be created by all phases of the project. 5.13.3. Fire protection. When a subdivision is to be served by a central water system or a public water system, the subdivision agent, in consultation with the county departments of emergency management and public utiliries, may specify the installation of fire hydrants. Hydrant location must be approved by the subdivision agent, but in no case may hydrants be spaced more than eight hundred (800) linear feet apart along a street or roadway. 5.14. Utilities (other than water and sewer). 5.14.1. Costs. The applicant shall be responsible for the installation of all improvements listed below, all of which shall be installed at no cost to the County of Isle of Wight unless otherwise provided in this ordinance. 5.14.2. Underground installation. All new transmission, distribution and customer service utility facilities, carrying or used in connection with electric power, telephone, telegraph, internet, cable television, petroleum, gas or steam, installed within the boundaries of any subdivision shall be placed below the surface of the ground; provided that: A. All required improvements shall be in accordance with accepted standards of utility practice for underground construction. B. Temporary overhead facilities required for construction purposes will be permitted; C. Equipment such as electric distribution transformers, transmission thirty-three (33) KV and above, switchgear, meter pedestals and telephone pedestals, which are normally installed aboveground in accordance with accepted utility practices for underground distribution systems may be so installed; D. Meters, service connections and similar equipment normally attached to the outside wall of the premises it serves may continue to be so installed; E. Whenever relocation of utility facilities is compelled by any construction undertaken by any unit of government, the provisions of this section may be waived by the board of supervisors or the subdivision agent; Page l6 of 21 F. Overhead farm and industrial customer utility services and wiring which is on property owned and/or occupied by the property owner or user is allowed; G. With the exception of cluster/sliding scale "by-right" development, underground utilities will not be required in those areas of the county zoned rural agricultural conservation (RAC); H. Overhead utilities services existing as of October 29, 1974, may be repaired, replaced or increased in capacity, and relocated parallel and adjacent to pre-existing state roads; I. Overhead utilities services may be extended within a subdivision where the average lot size (excluding the original parcel) is at least five (5) acres and may further be extended in any case where such extension would be parallel and adjacent to public roads existing as of services along roads not existing as of October 29, 1974, and internal to a subdivision where the average lot size (excluding the original parcel) is five (5) acres or less must be underground. Overhead utilities services may be extended along or across other public roads as authorized by the subdivision agent. 5.15. Easements. 5.15.1. Easements must be provided for water, sewer, power lines, landscape, open space, access and no-access, maintenance, future road expansion, drainage, greenways, sidewalks and multi-use paths, and other utilities in the subdivision when required by the subdivision agent. 5.15.2. All utility easements must be a minimum of ten (10) feet in width unless a narrower easement width is expressly authorized by the subdivision agent. Easements wider than ten (10) feet may be required by the subdivision agent. 5.15.3. No easements or utility rights-of-way may be relocated or altered without the express written consent of all persons holding any interest in the easement. 516. Traditional neighborhood design (TND). The objective of the traditional neighborhood design type is a compact, pedestrian-scaled development incorporating a diverse, mixed range of uses to promote community interaction, convenience, housing options for all income levels, and civic participation. The following regulations are offered to guide this type of development in accordance with design principles compatible with the historic nature of the county, and in harmony with the applicable county ordinances and the comprehensive plan. A. Applicability. These provisions apply to new developments of fifty (50) acres or more, zoned PD-R, PD-MH, and PD-MX. In the case of expanding existing subdivisions of ten (]0) lots or mare, these guidelines can be applied to any development residentially zoned and proposing at least five (5) additional lots. The following standards do not exempt the applicant from compliance with the other sections of this ordinance which protect the general health, safety, and welfare of residents. B. Development standards. Page 17 of 21 L [Location:]All residents should be within approximately one-fourth ('/a) mile radius or a five-minute walk from existing or proposed commercial, civic, and open space areas. 2. Open space: At least forty (40)percent of the gross acreage of the traditional neighborhood development must be open space. Open space may include undevelopable areas such as steep slopes and wetlands, and stormwater detention and retention basins. At least fifty (50) percent of the open space must be common open space dedicated to the public for recreation. Additionally, ninety (90) percent of the dwelling units shall be within a one-fourth ('/a) mile radius or a five- minute walk from common open space. 3. Stormwater management: The design of the traditional neighborhood development should minimize off-site stormwater runoff,promote on-site filtration, and minimize the discharge of pollutants to ground and surface water. Natural topography and existing land cover should be maintained/protected to the maximum extent practicaL New development shall meet the standards of section 5.8, stormwater management. 4. Lot and block standards: A. Street layouts should provide for blocks that are a minimum of two hundred fifty (250) feet in length and a maximum of five hundred (500) feet in length; however, longer length shall be allowed with mid-block pedestrian pass- throughs every five hundred(500) feet. B. Blocks should be wide enough to allow two (2) tiers of lots at minimum depth as required by the underlying zoning. The subdivision agent may approve a single tier of lots of minimum depth where environmental conditions restrict the lot layout. C. A variety of lot sizes should be provided to facilitate housing diversity and choice and meet the projected requirements of people with different housing needs. C. Circulation standards. The circulation system shall allow for different modes of transportation. The circulation system shall provide functional and visual links within the residential areas, mixed use area, and open space of the community and shall be connected to existing and proposed external development. The circulation system shall provide adequate traf�c capacity, provide connected pedestrian and bicycle routes (especially off-street bicycle or multi-use paths or bicycle lanes on the streets), control through traffic and promote safe and efficient mobility through the neighborhood. All TND transportation elements should be presented to the locality and VDOT for discussion and approval of unique features. 1. Pedestrian circulation. Convenient pedestrian circulation systems that minimize pedestrian-motor vehicle conflicts shall be provided continuously throughout the TND. Where feasible, any existing pedestrian routes through the site shall be preserved and enhanced. All streets, except far alleys, shall be bordered by sidewalks on both sides. The following provisions also apply: Page 18 of 21 l. Sidewalks in residential areas. Clear and well-lighted sidewalks, five (5) feet in width, shall connect all dwelling entrances to the adjacent public sidewalk. 2. Sidewalks in mixed use areas. Clear and well-lighted walkways shall connect building entrances to the adjacent public sidewalk and to associated parking areas. Such walkways shall be a minimum of five (5) feet in width. 3. Disabled accessibility. Sidewalks shall comply with the applicable requirements of the Americans with Disabilities Act and VDOT standards. 4. Crosswalks. Intersections of sidewalks with streets shall be designed with clearly defined edges. Crosswalks shall be well lit and clearly marked with contrasting paving materials at the edges or with striping. In addition, curb extensions shall be incorporated where pedestrian facilities intersect higher- volume streets within the development to protect parking areas and reduce pedestrian crossing times. 2. Bicycle circulation. Bicycle circulation shall be accommodated on streets and/or on dedicated bicycle paths. Where feasible, any existing bicycle routes through the site shall be preserved and enhanced. Facilities for bicycle travel may include off-street bicycle multimodal paths and separate, striped, five-foot bicycle lanes on streets. If a bicycle lane is combined with a lane for parking, the combined width should be thirteen (13) feet and the bicycle travel lane shall be located between the vehicular travel lane and parking lane. 3. Public transit access. Where public transit service is available or planned, convenient access to transit stops shall be provided. Where transit shelters are provided, they shall be placed in highly visible ]ocations that promote security through surveillance, and shall be well-lighted. 4. Motor vehicle circulation. Motor vehicle circulation shall be designed to minimize conflicts with pedestrians and bicycles. Traffic calming features such as "queuing streets," curb extensions, traffic circles, and medians may be used to encourage slow traffic speeds. Arterial streets should not bisect a TND if pedestrian cross- access is not feasible. a. Street hierarchy. Each street within a TND shall be classified according to section 5.9.5 of this ordinance. 5. Street layout. The traditional neighborhood development should maintain the existing street grid, where present, and restore any disrupted street grid where feasible. In addition: i. Intersections shall be at right angles whenever possible, but in no case less than seventy (70) degrees. Low volume streets may form three-way intersections creating an inherent right-of-way assignment (the through street receives precedence) which significantly reduces accidents without the use of traffic controls. ii. Corner radii. The roadway edge at street intersections shall be rounded by a tangential arc with a radius of�fteen (l5) feet for local streets where the receiving street is projected to have less than four hundred (400) vehicle trips Page 19 of 21 per day, and twenty-five (25) feet for intersections involving collector or arterial streets. Any reduction or increase in the proposed corner radii shall be subject to the approval of VDOT. The intersection of a local street and an access lane or alley shall be rounded by a tangential arc with a maximum radius of ten (]0) feet. iii. Curb cuts for driveways to individual residential lots shall be prohibited along collector and subcollector streets with residential access recommended from alleys only. Additionally, curb cuts shall be limited to intersections with other streets or access drives to parking areas for commercial, civic or multifamily residential uses. Clear sight triangles (twenty-five (25) feet x twenty-five (25) feet) or as approved by VDOT shall be maintained at intersections unless controlled by traffic signal devices. iv. The orientation of streets should enhance the visual impact of common open spaces and prominent buildings create lots that facilitate passive solar design, and minimize street gradients. All streets shall terminate at other streets or at public land, except local streets may terminate in stub streets when such streets act as connections to future phases of the development. Local streets may terminate other than at other streets or public land when there is a connection to the pedestrian and bicycle path network at the terminus. 6. Parking requirements. Parking areas for shared or community use should be encouraged. The number of parking spaces shall be in accordance with the zoning ordinance requirements. In addition: a. In the mixed use area, any parking lot shall be located at the rear or side of a building. b. A parking lot may not be adjacent to or opposite a street intersection. c. A shared parking agreement must be established and approved by the zoning administrator prior to site plan approval. d. Parking lots or garages must provide not less than one (1) bicycle parking space for every ten (10) motor vehicle parking spaces. e. Paving. Reduction of impervious surfaces through the use of interlocking pavers is strongly encouraged for areas such as remote parking lots and parking areas for periodic uses. 7. Guidelines for lighting. a. Street lighting shall be provided along all streets. Generally more, low- intensity lights, as opposed to fewer, high-intensity lights, should be used. Street lights shall be installed at all street intersections (including alleys), at the end of all cul-de-sac streets, and on both sides of a street, alternating from one side of the street to the other at intervals of three hundred (300) to four hundred (400) feet. Lights shall not exceed ten thousand (10,000) lumens and shall be directed downward and opaquely covered at the top. Regardless of type of fixture and bulb and illumination characteristics, street lighting design shall follow dark sky guidelines and principles. Page 20 of 21 b. Exterior residential lighting shall be shielded and directed downward in order to reduce glare onto adjacent properties. c. All commercial lighting shall be in compliance with article 1 1 of the zoning ordinance. 8. Landscaping and screening standards. Overall composition and location of landscaping shall complement the scale of the development and its surroundings. In general, larger, well-placed contiguous planting areas shall be preferred to smaller, disconnected areas. Plant materials, specifications, installation and maintenance shall be in accordance with the zoning ordinance landscaping requirements. a. Street trees. A minimum of one (1) deciduous canopy tree per forty (40) feet of street frontage per street side, shall be required. Trees can be clustered and do not need to be evenly spaced.Trees should be located between the sidewalk or within a landscape easement adjacent to the right-of-way with the maintenance responsibility assigned to a property owner's association. Species of trees should be consistent with the recommendations found in the VDOT Subdivision Street Design Guide which will not interfere with nearby utilities or other public improvements. 5.17. Solid waste refuse collection. All subdivision lots on new streets in subdivisions platted subsequent to August 1, ]997, shall be required to utilize the door-to-door solid waste refuse collection by the duly authorized and franchised collectors and haulers as determined by the board of supervisors of Isle of Wight County, Virginia. (Ord. No. 2012-11-C, 10-18-12.) Page 2l of 21 SIGNATURE PAGE Date: June 15, 2023 ��� .�.�, -�----^� Read and Passed: -- Chairman Teste: c� � Clerk Approved as to Form: Robert W. Jo s, Jr. County Attorney